DELTA... THE RIGHT LIGHT...

FTE 4x4 Specialists Ltd. is please to announce that they are now a dealer for Delta Tech Industries otherwise known as Delta Lights, they offer a very diverse range of lights covering all aspects of vehicle lighting especially Jeeps. Below is just a sample of what they have on offer specifically for the Wrangler TJ & JK, to check out there full range of lights go to Delta Lights website.

The Delta Quad bar Xenon Hi/Low Headlight Set for Wrangler TJ and JK with city light (side light) has built-in steel armour protecting the element. The series come with an adapter converting H4 system to H13.The headlights feature lead-crystal prismatic glass lens, vacuum metalized steel reflectors and rubber boot to seal from dust and moisture. It will outperform factory headlights 4 to1. They are also “E” Marked which makes them legal for use in the UK.

 

 

 

Delta Windshield T-Bracket Set was designed specifically for Jeep Wrangler both the TJ and JK. They are constructed of machined billet aircraft aluminium and use existing windshield bolt holes and thus requiring NO DRILLING. The brackets were designed for universal application and every brand of lights.

Delta Hood Light Bar was specifically developed for Jeep Wrangler JK & TJ 1997-11. It was designed to complement the Delta SkyBar and vehicle exterior design using the existing factory bolt holes thus requiring NO DRILLING. The Hood Bar is constructed of plasma cut powder coated steel cross bar and machined billet aluminium mounting arms. The Bar offers a vertical swivel for precision aiming and it comes with pre-terminated 3 (ea) Xenon 55 Watt driving lights producing an impressive beam of light for night trail adventures. Total draw 13.75 Amps, also available with 6000K HID driving lights producing an incredible powerful white “daylight” beam of light for night trail adventures. Total draw 8.75 Amps. The lights come equipped with hard plastic covers. The set is also equipped with a complete OEM harness, relay, switch and fuse.

Delta fender Light Set was specifically designed for Jeep Wrangler both TJ and JK. The set is well integrated with headlamp and fender design. It is constructed from 13 ga. powder coated plasma cut steel encasing 3” dia. waterproof xenon driving lights or Delta 6000K HID system, which will produce an impressive long range white, near daylight bright light for any type of night driving. Each light offers a full micro-adjustment for aiming. They mount to existing bolts on each front fender. NO DRILLING required.

 

 

 

 

Delta Bumper Driving Lamp Set for the Wrangler JK is an upgrade to factory low wattage fog lamps. The Xenon 55 Watt driving lamps are configured into the billet aluminium face rings which provide micro adjustment for horizontal and vertical aiming. The Driving Light set comes with its own upgraded stand-alone OEM wire harness, Illuminated switch, relay and fuse. These lights will give you an increased long-range visibility when driving on narrow trails or in any adverse weather condition. Also available with the Delta 6000K HID system 

SkyBar™ - Wrangler Light Bar JK &TJ

Delta SkyBar was specifically designed for Jeep Wrangler TJ and JK. It is constructed of machined Billet Aluminium mounting arms and spacers and plasma cut 13 ga. Steel cross bar holding a battery of 6 xenon driving lights. The integrated design of the SkyBar complements the roof-line and the unique lines on Jeep Wrangler. It is designed to allow garage clearance with any lifts. The bar does not interfere with any roof, soft or hard top. The bar features a built-in deflector to eliminate glare. The light bar is wired to allow 3 phases of operation 2, 4 and all 6 lights for your full control in using just the right amount of light power from 110W to 330W with the max. Draw of 27.5Amp. The light bar offers a precision vertical aiming adjustment. The mounting billet arms attach to the side by the windshield to existing bolt holes thus requiring NO DRILLING. The SkyBar comes complete pre-wired with an OEM double harness, two switches, relays, fuses and all necessary hardware.

As I said at the begin of this article this is a very small selection of the lights that Delta have on offer, so please check out there website to see the full range. Once you have seen a light set-up you like make a note of the part numbers and drop me an email at info@fte.co.uk or give me a ring on 07973 198483 for prices and delivery. I have met the guys behind this company and there enthusiasm for there product is great as are there products.

Technorati Tags: Jeep,Wrangler,JK,TJ,Off-Road,Lights,Light-Bars,Spots,Upgrades,Delta-Lights,HID,Xenon,SkyBar,Hood-Mount

Heavy Duty Front Ball Joint Sets For the Dana 30 /44 Axles

Fed up having to replace the knuckle ball joints on your Jeep because they just don’t seem to last, running over size tyres and off-set wheels puts a lot more strain on the knuckle ball joints. When you see what is inside the stock Jeep ball joint you will understand why they wear out so quick. The photo below shows a pair of stock ball joints stripped down.Well Synergy Suspension have the answer with there new heavy duty ball joint sets, available for the Jeep Wrangler JK, TJ/LJ, YJ, Cherokee XJ, and Grand Cherokee ZJ & WJ (Dana 30/44). Fully greasable sintered metal on bushing design.

• Designed to replace the factory ball joint that is prone to premature failure on lifted vehicles with large off-road tires
• Fully greasable sintered metal on bushing design that has high wear resistance
• Outperforms the factory ball joint assembly
• Ball joint boot is made from tear/wear resistant polyurethane
• Includes all necessary hardware for installation
• Single Set includes: (1) upper, (1) lower
• Complete Set includes: (2) upper, (2) lower
• 12 Month Unlimited-Warranty

Available from FTE 4x4 Specialists Ltd 07973 198483, who are now dealers for Synergy Suspension.

Technorati Tags: Jeep,Wrangler,Cherokee,Grand Cherokee,JK,TJ,XJ,YJ,ZJ,WJ,Off-Road,Suspension,Axle,Steering

New Products at the SEMA Show

They say the simple ideas are the best, from Vertically Driven Products comes a rubbish bin & cup holder, this unit fits into the rear existing cup holders. Unlike other products on the market this items will still give you a couple of cup holders as well. Available for Wrangler JK 2007 – 2012.

A new snorkel for the Wrangler JK will soon be available from Wild Boar, at present in the prototype stage but looking good, as soon as more information is available it will be here.
 

Rugged Ridge new aluminium front bumper for the Wrangler JK, weighting in at only 26.9lbs in standard configuration, when fitted  with the hoop over rider, stubby ends & winch mount plate overall weight is 62.6lbs

For more information contact Steve at FTE 4x4 Specialists Ltd, on info@fte.co.uk

Not All Wheel Spacers Are The Same

Recently I had a Cherokee XJ brought into me with some strange noises and even stranger handling, the ability for it to go in a straight line above 20mph was almost none existent without some serious sawing on the steering wheel! At first glance underneath nothing jumped out, the wheels did have a little bit of negative camber, but I have seen a lot worst. First point to check was the wheel hubs, but as soon as I removed the front wheels the true horror was apparent.

To push the stock wheels out to give clearance for the 31x10.50 tyres wheel spacers had been fitted, not normally a problem, if the they are the correct type and fitted correctly. But these particular spaces I have not seen fitted to vehicles since the late 70’s early 80’s. They use a screw on stud extension that is tightened onto the original hub / disc then a hollow cast spacer is slid over the extension studs and the wheels then fitted back on. They work, but are definitely not designed to be used for big tyre set-ups or off-road use.

In this instance they were dangerous, as they had not been fitted correctly, (the work had not been carried out by the current owner, he had only just taken possession of the Cherokee) as you can see from the photos the screw on extensions did not have a deep enough bore to allow them to be tighten on to the hub. So when the spacer plate was fitted it was floating, with the wheel fitted it pulled up against the hex section of stud extension so the whole loading was being placed on the five hexes, allowing the wheel to basically flex on the extension studs. This did not only cause the steering to wander, but put a lot of strain on the hubs and brakes as the discs were not clamped tight to the hubs, it caused excessive wear to the brake pads and discs which had to be changed. One hub survived the ordeal the the other was replaced.

New Rugged Ridge billet spacers were fitted. These are constructed of double anodized black extra thick 6061T6 Aluminium for long life and extra corrosion resistance. All hardware is grade 8 for extra strength. They include 10 pre-installed grade 8 wheel studs, 10 lug nuts and thread locker. So as you can see from the photos below not all wheel spacers are the same!

FTE 4x4 Specialists Ltd can supply the Rugged Ridge spacers, for more information send us an email to info@fte.co.uk

Technorati Tags: Jeep,Rugged Ridge,Off-Road,Wheel,Spacers,Handling,Wrangler,Cherokee

More Clearance For Under JK Rear Shock Mounts

If you own a Wrangler JK then you must have seen how low the the shock mounts sit on the rear axle, normally the pumpkin part of the axle is the lowest part but in the case of the Wrangler JK it is also the shock mounts.

Now there are many kits on the market that will raise the lower shock mounts on the axle, a very good example is Synergy Suspension units, it raises lower shock mount 1-3/8" higher than stock. Bolt-on design that strengthens the factory control arm mount and also provides a skid plate for the lower controls arm mount. In all one neat little package.

The only problem with raising the lower shock mounts is now your shock are to long and there is a good chance that the shock will now bottom out. One option would be to fit taller bump stops but this will limit the suspension travel. Well Synergy Suspension have the answer to this, in the form of a new upper shock mount, that is a bolt-in fit and will raise the upper shock mount by 2” (50mm), gain back the travel lost with raising the lower mounts. The brackets come powder-coated with all necessary hardware to install. Modification of stock exhaust will be needed to clear the factory sway bar.

Another option to improve the shock location and to stop the usually problem of the top bar pin is to use a bar-pin eliminator, Synergy Suspension make a neat bracket that works well with there upper shock brackets, although it could be used on the stock mounts just to get rid of the problem that occurs with the top bar pin mount.

FTE 4x4 Specialists Ltd. will soon be offering Synergy Suspension components to the UK, this is only a very small selection of the components they have. They cover most models of Jeep, TJ,JK, YJ,XJ, & ZJ and have some rather interesting parts on offer. As they say “watch this space”.

Synergy Suspension JK Rear Shock Mounts VIEW SLIDE SHOW DOWNLOAD ALL

Technorati Tags: Jeep,Wrangler,JK,Suspension,Off-Road,Synergy-Suspension,Shocks

Wrangler Resurrection is alive and kicking

 

Back at the beginning of February I wrote a blog about an old Wrangler and a new project called “Wrangler Resurrection” well it has not been forgotten, it is just that work has got extremely busy (no complaints) so my projects get moved onto the back burner. But I have been collecting parts ready to start, the rear suspension is going to be the first item to get a makeover. The Wrangler is already fitted with a Rubicon Express long arm kit, but to upgrade the rear suspension I am going to convert it over to a triangulated upper link, and remove the rear trac-bar. This should free up the suspension giving greater articulation, I am going to use a Rock Krawler weld-on rear axle mount and brace.

 

 

The upper spring mounts are also going to be altered using the
Black Diamond's Coil Correction Kit, this will corrects the curvature of the rear spring. Meaning they can do there job more efficiently, the problem is even evident at 3" of lift height, and becomes more of an issue as lift height increases. This incorrect coil loading results in lost ride height and a diminished "too soft" spring rate.

I Another item on the rear that is going to get modified is the shock mounts, at present I am undecided with which manufacturer to go with, but the intent is to turret the shocks outboard of the chassis. This will allow for greater articulation, and I will be using a Currie Enterprise coil spring retainer kit to make sure I do not pop any springs.

As for the front suspension I would like to convert over to coil overs, as I intend to change the front axle, to a high pinion unit then this will be the time I would do the work. There are many kits on the market to do this, again I am looking at using the Rock Krawler set-up. This involves cutting off the original spring/shock mounts from the chassis and welding in complete new mounts. Part of my reason to convert over to this style of front suspension is with the front diff angled correctly, the springs are bowed a considerable amount with with a 5.5” lift. One option is to cut the spring mounts of the axle and reposition them, but that seems like the ideal time to think of an upgrade!

Another item that is getting a serious makeover is the steering linkage, as once a Wrangler TJ (or a Cherokee XJ and Grand Cherokee ZJ) is lifted more then 4” then the steering is a compromise. There are many kits on the market is you own a LHD Jeep, but for us RHD owners the market is very limited. For the pass 12 months I have been trying different configurations and I am at long last very close to an answer. My main itinerary was it should be a bolt-on set-up, with the minimum of part changes, so it could be done by an owner of a vehicle rather then having to take the vehicle to a specialist workshop. As soon as I have tested the set-up, ( I have plenty of volunteers who want to test it for me) and am happy with the results, I will be publishing it here first. So as they say watch this space.

All parts that I am using in this project are available from FTE 4x4 Specialists Ltd so if you have any questions then feel free to contact me. Also don’t forget to check out our face book page  

Technorati Tags: Jeep,Wrangler,Suspension,FTE 4x4 Specialists,Rock Krawler,Rubicon Express,Steering

Independence Day: Mopar readies the Jeep Wrangler JK8 Independence Kit

So you want a Wrangler Pick-up truck, well as last Mopar are going to launch the JK-8 conversion kit, read more below.

The JK-8 gets a launch date. For those of you that have been patiently awaiting more details concerning Mopar’s Jeep Wrangler JK-8 Independence Kit, since it debuted in April at the Easter Jeep Safari in Moab, you can look forward to more than just fireworks July 4th weekend. The JK-8 Kits will be available at select dealerships beginning July 4th weekend.

Jeep and Mopar are pushing hard on suppliers to have 100 of the kits available by July 4th, a source within Mopar’s development team revealed. In all Jeep has 1000 of the kits in production, and is working hard to coincide the JK8 Independence’s launch with our country’s own Independence Day.

No word yet, on product mix of how many kits will be bolt on versus weld on. We assume that all 100 kits available on July 4th will be the less expensive and easier to install bolt on version. The bolt on kit will have a retail of just under $5,000. No word yet on the Mopar part number or which dealership will receive the initial kits. -But we can tell you the kits will come with a Mopar certificate of authenticity and die cast aluminium fender emblems bearing the “JK-8″ ensignia, similar to those used on the 1981-1986 Jeep CJ8 Scrambler.

The name of the pickup truck conversion kit and the July 4th Independence Day launch were apparently planned late last year. The move to name the JK8 Kit “Independence” is a nod to Jeep’s historical significance during World War II and coincides with Jeep’s own 70th Anniversary.

 

 

Watch a time lapsed build of the JK8 performed by the Mopar team at the recent Easter Jeep Safari in Moab:

Technorati Tags: Jeep,Wrangler,JK,JK-8,Mopar